How To Build a Carport Attached To The Side Of Your House (2023)

  • chad
  • July 17, 2007
  • Construction How-To, Garages
(Video) How to Build a Lean To Shed

By Monte Burch

A carport, or lean-to shed, attached to an existing building such as a garage, barn, shed or the side of your house can provide economical shelter for vehicles, garden tractors, boats or other equipment. An attached carport is also fairly easy to construct against the side of another building, if you have enough height under the existing building eave.

The carport/lean-to shown uses basic and simple pole-building construction techniques, and was added to an existing workshop. The outer end of the shed is supported by Wolmanized pressure-treated 4-by-4 posts. And because the outer fascia is exposed to the weather it is constructed of 1-by-6 pressure-treated materials as well. Lightweight, but strong, metal is used for the roofing. A somewhat different approach was used for the roof framing. Traditional pole-building, metal-roof construction consists of 2-by-4 purlins fastened on edge across the rafters with the metal roofing fastened down on these. This allows a space where sparrows and other birds can get out of the weather and even a place to build their nests, with the resulting mess. Our design utilizes 2-by-4 blocking positioned between the rafters and located against the top edges of the rafters. This prevents birds from resting under the roof and keeps droppings off boats, cars or other equipment.

(Video) DIY Carport Build

The shed shown, withstood 3 inches of ice and an additional 18 inches of snow, which fell this winter. The design may, however, not be strong enough or have enough roof slope for some high-snow areas. Check with local building codes and regulations. The shed shown is 24 feet long to match the existing building length, and 15 feet deep. The latter allows for standard 16-foot 2-by-6’s for rafters. You may have to alter the design somewhat to suit your existing building height, length, even the width if you desire a narrower shed. It’s a good idea to make a rough sketch of the building, to determine the roof pitch, number of support posts needed and so forth.

How To Build a Carport Attached To The Side Of Your House (5)

Getting Started

First step is to locate and install the support header on the existing building. The end of the header should set back from the edge of the existing building by 1/2 inch, plus the thickness of any siding and trim that will be added. Mark the location of one end of the header and then mark the other end. Make sure the header is level end-to-end. Fasten the header in place with lag screws through the siding and into the studs of the existing building. Drop a plumb line from each corner of the header and mark this location on the bottom of the existing building. This will give you a starting point to layout the building and determine the location of the support posts. Beginning at one plumb line mark, attach a string to the building. Measure the length needed for one end, drive a stake and fasten the string in place. Beginning at the second plumb line mark, measure for the opposite end, temporarily drive a stake and add a second string line. Measure the distance between the two plumb-line marks for the length of the carport. Measure between the two stakes and adjust the stakes as needed to achieve the same distance.

Make sure the carport is laid out square with the existing building. One method of ensuring square is with right angle string lines. Beginning at one of the plumb line marks, measure 3 feet out from the building on the string and mark this with a felt tip pen. Measure 4 feet along the building wall and mark this measurement as well. Measure diagonally between the two marks. The measurement must be 5 feet to create a square corner. Move the string-end stake in or out to achieve the correct measurement. This creates a square corner for one end of the carport and determines the location of the corner post. Repeat for the opposite end and corner post. Then, again measure between the two stakes to make sure the length is correct. You can also check for squareness by measuring diagonally from the plumb line marks to the opposite outside corner locations. The measurements should be the same. With the corner post locations determined, run a string line from corner post to corner post and mark the locations of the other three posts.

Construction

The posts can be set on and anchored to concrete piers poured in holes in the ground. Or you may be able to utilize pre-cast piers. Another method is to set the posts in the concrete. In this case, pressure-treated posts must be used. Again, check with local building authorities as to methods suitable for your area. Regardless of the method of erecting the posts, make sure they are positioned correctly to create a square construction, again checking with a string and the triangular method. Also make sure the posts are plumb, bracing them in place two ways with temporary stakes and 2-by-4 braces.

(Video) MUST LOOK !!! 24+ Carport Ideas For Side Of House 2018

With a helper, hold an end board (rafter) up against the existing house wall and against the end of the support header. Determine the location of the end rafter on the end post, as per pitch or outer roof height needed. Mark the rafter bottom edge location on the end post. Also mark the angle of the end of the rafter against the existing building; it must be cut so it will fit snugly against the building wall. Measure for rafter length, allowing for overhang, and cut the angle. Cut the same angle on the outer end of the rafter as well. Repeat for the opposite end of the building. Then use one of the cut rafters as a pattern to cut the remaining rafters.

Fasten the front support beam in place to the posts, locating it below the rafter bottom edge line marked on the posts. This beam is actually made up of three 12-foot lengths on the building shown. Make sure the beams are level. Locate the positions of the rafters on the header and fasten joist hangers in place. Fasten the rafters in place in the joist hangers with their outer ends resting on the outer support beams.

Fasten the opposite end of the rafters to the support beams with metal hurricane bracing plates. Cut the post tops level with the rafters. Fasten a second inner support beam up against the bottom edges of the rafters and to the inside of the posts. Cut the end support beams. Note the outer end may have to be cut at an angle to fit up under the rafter, depending on roof height and pitch. The existing building end must be fastened to a block anchored to the existing wall. The outer end is fastened to the post and/or rafters. Cut blocking pieces to fit between the end rafters and the end support beams. Fasten in place on 24-inch centers by toenailing one end, or use angle braces.

Next, cut and install the braces. The front braces have a 45-degree angle on both ends. The end braces are best cut by first cutting the bottom 45-degree angle, positioning a brace in place and marking the top angle to fit the end beam. With the end braces in place, cut and install siding over the ends. You may also wish to add trim around the ends to match the existing building. A fascia board is fastened to the front of the rafter ends to finish off the outer end.

The building shown was covered with metal roofing. The roofing is brown to match the shingles on the existing building. Other choices include a variety of polycarbonate materials, such as SunTuf. A gravel, or better yet, concrete floor, can add to the usefulness of the carport.

Tools & Supplies

  • Support posts, 4×4” x 10’, 5 req’d.
  • Headers, 2×8” x 12’, 2 req’d
  • Joists, 2×6” x 16’, 17 req’d
  • Front beams, 2×6” x 12’, 4 req’d
  • End beams, 2×8” x 16’, 2 req’d
  • Front braces, 2×6” x 3’, 8 req’d
  • Side braces, 2x4x12”, cut to fit, 4 req’d
  • Blocking, 2×4” x 16”, cut to fit between rafters, 80 req’d
  • Roofing of choice, 16×24’
  • Fascia, 2×8”x12’, 2 req’d.

Related Posts

(Video) How To Install Posts And Beams For A Carport - DIY At Bunnings
(Video) How to Build a Carport Attached to the House (Step By Step Process)

FAQs

How do you attach a carport to the side of a house? ›

Extreme How To - Build an Attached Carport - YouTube

How do you build a lean to side of a house? ›

How To Build A Lean To On An Existing Building - YouTube

How close to property line can I build a carport? ›

The garage or carport shall not be closer than five feet to the front property line, or closer to a side property line than the setback required for the primary structure on the same parcel. b.

Does a carport add value to a house? ›

Yes, adding a metal carport will increase the value of your home. This means you can increase your asking price when listing your home and you may get more interest and better offers from potential buyers. Protect your vehicles from weather damage.

Do carports need footings? ›

Carports do not require foundations, but they must be stable enough to keep from blowing over at the first breath of a breeze. The sturdiest method is to secure the support posts a minimum of 2 feet deep, in poured concrete.

Do I need planning permission for a lean-to on the side of my house? ›

You can add a lean-to conservatory without planning permission to your home, as long as it is within the boundaries of your property and doesn't cover over 50% of the total area.

How big can a lean-to be without planning permission? ›

Permitted Development rules

It is within the boundaries of the property and won't cover more than 50% of the total area. No part of the extension is higher than the eaves of the house. The eaves are no more than three metres high if you are within two metres of the property's boundary.

How do you attach a patio roof to the side of a house? ›

How to attach a patio or verandah to a house - YouTube

How do you frame a carport wall? ›

Turning a Carport Into an Enclosed Garage- DIY Framing| Pt. 1 - YouTube

How do you attach a lean to existing metal building? ›

How To Add a Lean To on a 40x52 Metal Building - YouTube

How much does it cost to enclose a carport and make it a garage? ›

Converting a carport to a garage typically is less expensive than having a contractor build a new garage—provided the carport's slab, support posts, and roof are in good shape. On average, expect to pay $9,000 to $11,000 for labor costs alone to have a carpenter finish off the walls and install doors.

How do you build a lean to side of a garage? ›

How to Build a Lean To Shed - YouTube

Videos

1. My Carport Build - Part 1
(Khoa Phan)
2. MUST LOOK !!! 24+ Carport Ideas Attached To House 2018
(Sydney News 24)
3. Structural Tips for Carport Construction - Building Tips and Advice
(gregvancom)
4. April Wilkerson Response on How to Build an Open Carport - SketchUp
(ArtisanTony)
5. Carport on a mobile home
(maxam home repair)
6. What To Do Before Building A Carport - DIY At Bunnings
(Bunnings Warehouse)
Top Articles
Latest Posts
Article information

Author: Carmelo Roob

Last Updated: 12/14/2022

Views: 6432

Rating: 4.4 / 5 (65 voted)

Reviews: 80% of readers found this page helpful

Author information

Name: Carmelo Roob

Birthday: 1995-01-09

Address: Apt. 915 481 Sipes Cliff, New Gonzalobury, CO 80176

Phone: +6773780339780

Job: Sales Executive

Hobby: Gaming, Jogging, Rugby, Video gaming, Handball, Ice skating, Web surfing

Introduction: My name is Carmelo Roob, I am a modern, handsome, delightful, comfortable, attractive, vast, good person who loves writing and wants to share my knowledge and understanding with you.